Steps To Replace A PVC Pipe
Author: Scott Rodgers |
Though most of the plumbing tasks are minor enough for even a novice to handle but the easiest of them all is the replacement of the broken or cracked PVC pipes. Such a project also calls for an immediate repair as neglecting the issue may disturb your financial budget to a large extent.
Though most of the plumbing tasks are minor enough for even a novice to handle but the easiest of them all is the replacement of the broken or cracked PVC pipes. Such a project also calls for an immediate repair as neglecting the issue may disturb your financial budget to a large extent.
Since PVC pipes are prone to repeated cracks and leaks, their inspection must be a regular feature in your annual itinerary.
Start assembling all the plumbing tools and equipments that would be required during the project. Common plumbing tools such as pipe wrenches, pliers and Teflon tape are a regular feature in any plumbing project. In addition this particular assignment would require a pair of channel lock pliers, a hacksaw and a sealant compound. You would also need a particular length of PVC pipe that would actually replace the broken PVC pipe.
Before the commencement of the project, turn off the main water supply from the water control valve. Once water supply is cut off, move to the project site and observe the crack in the PVC pipe. With the help of tape, mark down the position on either side of the crack from where the pipe is supposed to be removed. Keep a margin of about six inches on both sides of the crack while marking down.
Before the commencement of the project, place a large-sized container just below the pipe such that no water falls down on the floor. Also a towel or a piece of cloth is tied to the affected area to absorb any water leftover.
Grab a hack saw and start cutting the pipe from the defined mark. Drain down the water from the pipe to the bucket/container and move to the other end of the pipe. Cut it in a similar way such that a particular length of pipe is dissociated from the fixture. Take the dissociated pipe to a local hardware store and demand a similar length of the pipe. Also the width of the new pipe must be absolutely similar to that of the old one. Buy a set of couplings that would serve the purpose of holding the new PVC pipe to the old fixture.
Connect the couplings on either end of the old pipe and apply some sealant on the setup. Once the compound has dried off, attach the new pipe to the couplings and render final finish to the fixture by applying a good amount of sealant on the binding.
Call a professional to handle the complications involved in the project.
Though most of the plumbing tasks are minor enough for even a novice to handle but the easiest of them all is the replacement of the broken or cracked PVC pipes. Such a project also calls for an immediate repair as neglecting the issue may disturb your financial budget to a large extent.
Since PVC pipes are prone to repeated cracks and leaks, their inspection must be a regular feature in your annual itinerary.
Start assembling all the plumbing tools and equipments that would be required during the project. Common plumbing tools such as pipe wrenches, pliers and Teflon tape are a regular feature in any plumbing project. In addition this particular assignment would require a pair of channel lock pliers, a hacksaw and a sealant compound. You would also need a particular length of PVC pipe that would actually replace the broken PVC pipe.
Before the commencement of the project, turn off the main water supply from the water control valve. Once water supply is cut off, move to the project site and observe the crack in the PVC pipe. With the help of tape, mark down the position on either side of the crack from where the pipe is supposed to be removed. Keep a margin of about six inches on both sides of the crack while marking down.
Before the commencement of the project, place a large-sized container just below the pipe such that no water falls down on the floor. Also a towel or a piece of cloth is tied to the affected area to absorb any water leftover.
Grab a hack saw and start cutting the pipe from the defined mark. Drain down the water from the pipe to the bucket/container and move to the other end of the pipe. Cut it in a similar way such that a particular length of pipe is dissociated from the fixture. Take the dissociated pipe to a local hardware store and demand a similar length of the pipe. Also the width of the new pipe must be absolutely similar to that of the old one. Buy a set of couplings that would serve the purpose of holding the new PVC pipe to the old fixture.
Connect the couplings on either end of the old pipe and apply some sealant on the setup. Once the compound has dried off, attach the new pipe to the couplings and render final finish to the fixture by applying a good amount of sealant on the binding.
Call a professional to handle the complications involved in the project.
Information:
Scott Rodgers is an acknowledged author who has been providing great guidance on plumbing works all over the country. His amazing knowledge and expertise has, in fact, sparked significant rise in revenue for talented plumbers across the nation, from Woodlake Plumbers (Need one? click here!) to Carlsbad Plumbers (Need one? click here!).
| < Prev | Next > |
|---|